I always end up in decision paralysis because I think of way too many possibilities. Is there a way I can avoid brackets? If I am able to drill into studs should I just use normal wood screws? I’ll be using it as a tea/spice shelf.

  • Barbacamanitu@lemmy.world
    link
    fedilink
    arrow-up
    2
    ·
    edit-2
    1 year ago

    If those hooks on the top corners are a multiple of 16" apart, and they line up with studs, you could use some 2-3" screws through those into studs.

    If they don’t line up with studs, you could stain a piece of lumber close to the same color and screw it to the wall through the studs and screw the shelf down to that board. It would act as a ledge for one of the shelves to sit on.

    There’s no back so there’s no easy way to directly screw this shelf to the wall. You’ll have to get creative.

    You could find the studs and put screws angled through one of the shelves into the studs. Screw from underneath the shelf if it’s lower than eye level, above the shelf if it’s above eye level. This is so you don’t see the screws.

    You could get realy fancy and use a pocket hole jig to make nice holes for your angled screws.

    • MrZee@lemm.ee
      link
      fedilink
      English
      arrow-up
      1
      ·
      edit-2
      1 year ago

      This is good advice. OP, use studs, not anchors. I’ve never had good luck using wall anchors on drywall.

      if the spacing doesn’t work for studs, another option would be to use angle brackets hooked to the shelf and into a stud (optimally two studs).

      If the unit cannot span two studs, center the unit on one stud and put an angle bracket on each shelf into the stud, then anchor the corners using drywall anchors - the brackets should take care of most of the weight and I would think the drywall anchors would hold and provide stability.

      If the unit can span two studs, center the unit over those studs and do the same, attaching angle brackets under each shelf. At that point you can skip the drywall anchor rigamarole.

      Of course, the angle brackets would end up being visible, so you may want to paint them or camouflage them in some other way.

      • Barbacamanitu@lemmy.world
        link
        fedilink
        arrow-up
        1
        ·
        1 year ago

        If you can only hit one stud, you should hit it in two places vertically if possible. Bottom shelf and top shelf if you can. You can still add some anchors if you need, but that works for most things. I hang cabinets into single studs all the time just by screwing it in two spots. It will work as long as the shelf or cabinet is built well enough.

        • MrZee@lemm.ee
          link
          fedilink
          English
          arrow-up
          1
          ·
          1 year ago

          Good point. I hadn’t thought about the physics enough. As long as the shelves are sturdy, there would be no need to anchor the corners.

  • 🇰 🌀 🇱 🇦 🇳 🇦 🇰 ℹ️@yiffit.net
    link
    fedilink
    English
    arrow-up
    1
    ·
    edit-2
    1 year ago

    It’s got those little rings at the top for a screw. I’d make sure both can get into a stud and then use a good anchor screw that can go in pretty deep since that shelf looks pretty big and heavy. Tho maybe it’s just the picture and it’s smaller than it looks. You did say it’s a spice shelf; from the pic it looks like it’s at least 3 feet tall and could hold a lot of books haha

    • ratboy@lemm.eeOP
      link
      fedilink
      arrow-up
      1
      ·
      1 year ago

      I’m thinking that will have to do. Would you suggest normal screws or should I play it safe and use wall anchors of some sort?

      • Screws into studs are always best when possible. Get yourself a stud finder. Even a basic one will do and they are super cheap these days. Like, less then $20.

        If you can get to two studs, wall anchors are unnecessary.